
On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
Best OverallVEVOR 60-Inch Clamp-On Forks9.7/10View on Amazon - 2
Most TinesGarvee 6-Tine Debris Forks9.6/10View on Amazon - 3
Best for LiftingRIGMEC Clamp-On Debris Forks9.6/10View on Amazon - 4
Best 48-Inch FitGarvee 5-Tine Pallet Forks9.5/10View on Amazon - 5
Lowest WeightYITAMOTOR 5-Tine Debris Forks9.4/10View on Amazon
Hay bales wait at the far end of the pasture and brush piles block the fence line, so the best clamp on forks for tractor work turn a loader bucket into a fork set without a quick-attach frame. Fork sets were compared by rated capacity, bucket fit, tine count, stabilizer bars and stated weight, using only what each maker publishes. The VEVOR set leads with an anti-tilt bar and adjustable stabilizer bar, while the Garvee debris fork set matches that rated capacity.
GoatGearLab earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
Quick picks
Best Overall VEVOR 60-Inch Clamp-On Forks: 4000 lbs capacity with an anti-tilt bar and adjustable stabilizer bar Check price on Amazon
Most Tines Garvee 6-Tine Debris Forks: six fork tines and 4000 lbs capacity for a 60-inch bucket Check price on Amazon
Best for Lifting RIGMEC Clamp-On Debris Forks: chain holes and Roll Back Protection Slots for chained loads Check price on Amazon
Best 48-Inch Fit Garvee 5-Tine Pallet Forks: 5 tines and 2500 lbs capacity for a 48-inch bucket Check price on Amazon
Lowest Weight YITAMOTOR 5-Tine Debris Forks: about 70.99 lbs with 5 tines for a 48-inch bucket Check price on Amazon
The gear we picked
| # | Product | GoatGear Score | Buy |
|---|---|---|---|
| 1 | VEVOR 60-Inch Clamp-On Forks | 9.7/10 | Buy on Amazon |
| 2 | Garvee 6-Tine Debris Forks | 9.6/10 | Buy on Amazon |
| 3 | RIGMEC Clamp-On Debris Forks | 9.6/10 | Buy on Amazon |
| 4 | Garvee 5-Tine Pallet Forks | 9.5/10 | Buy on Amazon |
| 5 | YITAMOTOR 5-Tine Debris Forks | 9.4/10 | Buy on Amazon |

VEVOR 60-Inch Clamp-On Forks
60-inch steel forks with a 4000 lbs rated capacity, an anti-tip bar and an adjustable stabilizer bar for tractor buckets.
Pros
- 4000 lbs rated capacity for logs, lumber, hay bales and pallets
- Anti-tip bar adds a support point against rocking on uneven loads
- Adjustable stabilizer bar keeps both forks aligned
- Triangle guide with a two-point fixing layout holds the forks steady on the bucket
Cons
- 100.31 lbs of fork weight counts against loader capacity
- No warranty term is stated
- Fork spacing needs adjusting for each different load
- Clamps need a wrench to finish and a tightness recheck before use

Garvee 6-Tine Debris Forks
Six fork tines for a 60-inch bucket with a 4000 lbs capacity, Q235 steel and a gloss black powder-coated finish.
Pros
- 4000 lbs capacity across six fork tines
- Q235 steel with a gloss black powder-coated finish
- Upgraded bolt design to reduce the risk of accidental detachment
- Fits a 60-inch bucket for pallets, logs, lumber and hay bales
Cons
- No warranty term is stated
- 110.78 lbs, the heaviest set here
- 31-inch fork length is shorter than the 42-inch Garvee 5-tine set
- Needs a bucket edge the forks can slide over and clamp

RIGMEC Clamp-On Debris Forks
Clamp-on debris forks for 48 to 60-inch buckets with a 2500 lbs capacity, chain holes and Roll Back Protection Slots.
Pros
- Chain holes let chains fix heavy loads to the forks
- Roll Back Protection Slots keep loads on the fork
- Durable welded steel with thick rectangular tube walls
- Fits 48 to 60-inch buckets with a universal design
Cons
- 2500 lbs capacity is lower than the 4000 lbs sets here
- Loads must sit evenly in the rear position during use
- Material weight plus fork weight must stay under the skid steer capacity
- Chain holes need chains to fix loads

Garvee 5-Tine Pallet Forks
5 fork tines for a 48-inch bucket with a 2500 lbs capacity and a rotate-to-lock clamp.
Pros
- 2500 lbs capacity with 5 tines for a 48-inch bucket
- Screw stated as 30% thicker for firm fixing
- Rectangular tube wall stated as 40% thicker
- Overall size of 42 by 31 inches for a compact fit
Cons
- 2500 lbs capacity is lower than the 4000 lbs sets here
- 84.11 lbs of fork weight counts against loader capacity
- Sized for a 48-inch bucket
- Compatibility covers most slide loaders, not all of them

YITAMOTOR 5-Tine Debris Forks
5 fork tines for a 48-inch bucket with a 2500 lbs capacity, at about 70.99 lbs.
Pros
- 2500 lbs capacity with 5 fork tines
- About 70.99 lbs, the lowest weight here
- Tines measure 21 by 2 by 2 inches
- Fits a 48-inch bucket or a bigger bucket
Cons
- 2500 lbs capacity is lower than the 4000 lbs sets here
- Plastic-sprayed surface, not a powder-coated finish
- Buckets must be less than 2 inches thick
- No anti-tip bar or stabilizer bar is stated
As an Amazon Associate I earn from qualifying purchases.
Also worth comparing
Clamp-On Pallet Fork Locking BoltsCheck price on Amazon
Nilight 2000lbs Clamp on Pallet Forks Fits 43'' TractorCheck price on Amazon
More picks to compare
YINTATECH 60-Inch Clamp-On Pallet Forks60-inch forks with 4000 lbs capacity and chain holes for a safe liftCheck on Amazon
YITAMOTOR 4000 lbs Debris Forks4000 lbs capacity for a 60-inch bucket or biggerCheck on Amazon
YITAMOTOR 60-Inch Pallet Forks 4000 lbsAdjustable stabilizer bar and anti-roll bar for 4000 lbs loadsCheck on Amazon
VEVOR 68.5-Inch Debris Forks 4560 lbs7 tines and 4560 lbs capacity for 68-inch bucketsCheck on Amazon
Garvee 60-Inch Pallet Forks 2000 lbsAdjustable stabilizer bar and 2000 lbs capacity for 60-inch forksCheck on Amazon
Spec comparison
| Fork | GoatGear Score | Capacity | Bucket fit | Fork length | Weight | Amazon |
|---|---|---|---|---|---|---|
| VEVOR 60-Inch Clamp-On Forks | 9.7/10 | 4000 lbs | 60-inch bucket | 60 in | 100.31 lb | View on Amazon |
| Garvee 6-Tine Debris Forks | 9.6/10 | 4000 lbs | 60-inch bucket | 31 in | 110.78 lb | View on Amazon |
| RIGMEC Clamp-On Debris Forks | 9.6/10 | 2500 lbs | 48 to 60-inch bucket | Not stated | Not stated | View on Amazon |
| Garvee 5-Tine Pallet Forks | 9.5/10 | 2500 lbs | 48-inch bucket | 42 in | 84.11 lb | View on Amazon |
| YITAMOTOR 5-Tine Debris Forks | 9.4/10 | 2500 lbs | 48-inch bucket or bigger | 21 in | 70.99 lb | View on Amazon |
Every spec repeats the brand’s rating from its listing (collected on 19 November 2026).
How to choose the best clamp on forks for tractor
Match capacity to your loader
Rated capacity is the first figure to check, and it must stay under the loader rating. The VEVOR set and the Garvee six-tine set are rated at 4000 lbs, while the RIGMEC, Garvee 5-tine and YITAMOTOR sets are rated at 2500 lbs. The RIGMEC maker says to keep the material weight plus the fork weight under the skid steer capacity, and to place cargo evenly in the rear position during use. Never exceed the loader or tractor rating. See our best tractor pallet forks for other fork styles.
Fit the bucket first
Bucket fit decides whether a set clamps on at all. The VEVOR set and the Garvee six-tine set fit a 60-inch bucket, the Garvee 5-tine and YITAMOTOR sets fit a 48-inch bucket, and the RIGMEC set fits 48 to 60-inch buckets. The YITAMOTOR set also fits a bucket bigger than 48 inches, and it suits buckets less than 2 inches thick. The VEVOR set slides onto a flat bucket edge, hand-tightens, and finishes with a wrench, with a tightness recheck before use.
| Fork set | Capacity | Bucket fit | Tines |
|---|---|---|---|
| VEVOR 60-Inch Clamp-On Forks | 4000 lbs | 60-inch bucket | Not stated |
| Garvee 6-Tine Debris Forks | 4000 lbs | 60-inch bucket | 6 tines |
| RIGMEC Clamp-On Debris Forks | 2500 lbs | 48 to 60-inch bucket | Not stated |
| Garvee 5-Tine Pallet Forks | 2500 lbs | 48-inch bucket | 5 tines |
| YITAMOTOR 5-Tine Debris Forks | 2500 lbs | 48-inch bucket or bigger | 5 tines |
Count tines and check the stabilizer
Tines spread the load across the bucket edge. The Garvee six-tine set has 6 tines, the Garvee 5-tine and YITAMOTOR sets have 5 tines each, and the VEVOR and RIGMEC sets state no tine count. A stabilizer bar keeps the forks aligned: the VEVOR set has an adjustable stabilizer bar with a seamless bar, and the RIGMEC set uses chain holes and Roll Back Protection Slots to keep loads on the fork. Compare the stabilizer and anti-tip features with the fork count before choosing. See pallet forks vs clamp on forks for how the two styles differ.
Weigh the set before you lift
Fork weight counts against the loader capacity, so it belongs in the math with the load. The YITAMOTOR set weighs about 70.99 lbs, the Garvee 5-tine set weighs 84.11 lbs, the VEVOR set weighs 100.31 lbs, and the Garvee six-tine set weighs 110.78 lbs. The RIGMEC set states no weight, so its weight cannot be compared here. A lighter set leaves more capacity for the load itself. See our best pallet forks for compact tractor for lighter fork options.
Around the Barn
- Slide the forks over the cutting edge and clamp them down, then recheck tightness before use.
- Set fork spacing to fit the load, and keep both forks aligned with the stabilizer bar.
- Place cargo evenly in the rear position during use, and keep the combined weight under the skid steer capacity.
- Check the clamps and bolts for tightness before each use, and clear debris and brush from the tines after the job.
FAQs from goat keepers
What size bucket do clamp-on forks fit?
The VEVOR and Garvee six-tine sets fit a 60-inch bucket, the Garvee 5-tine and YITAMOTOR sets fit a 48-inch bucket, and the RIGMEC set fits 48 to 60-inch buckets. The YITAMOTOR set also fits buckets bigger than 48 inches.
How much weight can clamp-on forks carry?
The VEVOR and Garvee six-tine sets are rated at 4000 lbs, and the Garvee 5-tine, YITAMOTOR and RIGMEC sets are rated at 2500 lbs. The RIGMEC maker also gives a working load range of 1500 to 4000 lbs; check before ordering.
Do clamp-on forks need tools to install?
The VEVOR set slides onto a flat bucket edge, hand-tightens, and finishes with a wrench. The Garvee sets slide over the cutting edge and clamp down to lock. Recheck tightness before use.
What keeps the forks from sliding off the bucket?
The VEVOR set uses an anti-tip bar, a triangle guide and a two-point fixing layout. The Garvee six-tine set uses an upgraded bolt design, and the RIGMEC set uses chain holes and Roll Back Protection Slots.
How heavy are clamp-on fork sets?
The YITAMOTOR set weighs about 70.99 lbs, the Garvee 5-tine set weighs 84.11 lbs, the VEVOR set weighs 100.31 lbs, and the Garvee six-tine set weighs 110.78 lbs.
Behind the Farm Score
The GoatGear Score weighs performance, build, value, safety and warranty. For clamp-on forks, safety means features that keep the forks on the bucket and the load on the forks, such as anti-tip bars, stabilizer bars, chain holes and Roll Back Protection Slots. 4 of the 5 sets state such safety features, and none of the 5 state a warranty term. How we pick explains the weights.
| Product | GoatGear Score | Perf. /35 | Build /25 | Value /25 | Safety /10 | Warranty /5 |
|---|---|---|---|---|---|---|
| VEVOR 60-Inch Clamp-On Forks | 9.7 | 32 | 22 | 21 | 7 | 0 |
| Garvee 6-Tine Debris Forks | 9.6 | 30 | 21 | 21 | 5 | 0 |
| RIGMEC Clamp-On Debris Forks | 9.6 | 28 | 21 | 20 | 7 | 0 |
| Garvee 5-Tine Pallet Forks | 9.5 | 28 | 20 | 20 | 3 | 0 |
| YITAMOTOR 5-Tine Debris Forks | 9.4 | 27 | 19 | 20 | 0 | 0 |
We translate each weighted point total onto the 9.2 through 9.8 band; ranks never flip, because the conversion is linear.
More from the barn
See every Tractor Attachments guide and all Tractor and Farm Implements guides. Also see our best tractor pallet forks. Also see our best pallet forks for compact tractor. Also see our pallet forks vs clamp on forks. Also see our best heavy duty pallet forks. Also see our best bolt on pallet forks. Also see our best grapple pallet forks. Also see our hay fork vs bale spear. Also see our best loader bucket for lawn tractor.
More picks: best landscape rake for tractor, best post hole digger for compact tractor, best tractor snow blade and best dump cart for lawn tractor.
