Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How Does a Moisture Meter Work: Hay Bale Readings Explained

How a hay moisture meter reads bale moisture with a long probe, and what its range, temperature reading and calibration clip mean at the barn.

How Does a Moisture Meter Work: Hay Bale Readings Explained
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Digital Portable Hay Moisture Meter Tester with 15.7" ProbeDigital Portable Hay Moisture Meter Tester with 15.7" ProbeView on Amazon
  2. 2ZOEYEC TK100H Portable Hay Moisture Meter for Cereal StrawZOEYEC TK100H Portable Hay Moisture Meter for Cereal StrawView on Amazon
  3. 3Pokiphip TK100H Portable Hay Moisture MeterPokiphip TK100H Portable Hay Moisture MeterView on Amazon
  4. 4Grain Hay Moisture Tester MeterGrain Hay Moisture Tester MeterView on Amazon
  5. 5AgraTronix 07100AgraTronix 07100View on Amazon

A bale that feels dry on the outside can still hold damp hay in the middle, and damp hay in the stack is the kind of quiet problem that shows up later as spoiled feed and wasted work. A moisture meter earns its place in the barn because it answers how does a moisture meter work in plain terms: push a probe into the bale and read the moisture inside, before the bale goes into storage. This guide explains the probe, the reading and the calibration step, using only the figures the listings state.

Also worth comparing

GoatGearLab earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

How does a moisture meter work: the short answer

A hay moisture meter reads moisture through a metal probe pushed into the bale. The probe reaches below the surface, where the outside of the bale cannot tell you what is going on, and the meter shows the reading on a backlit LCD screen. The Runant listing states the working principle is conductivity, with automatic temperature compensation, so the reading adjusts for the temperature of the hay.

Using one is a short routine: push the probe straight into the bale, hold the button, and read the screen. The Soonkoda listing describes pressing and holding the red button on the handle after the probe is in place, at which point the screen display jumps from “P1” to the measured moisture value. The Courdom listing adds a 3-minute auto-shutoff and glove-friendly buttons for early morning work in the barn.

If you would rather start with the hardware, our hay feeder guides cover the racks and bags that hold the hay these meters check.

Meter styles compared

Meter Probe Stated moisture range Temperature reading
Courdom HT-M 20 inch probe 8% to 45% 32°F to 210°F
AgraTronix HT-Pro 20 inch probe 8% to 44% Not stated
Soonkoda HM-B 15.7 inch probe 3% to 40% Not stated
Runant TK100H Probe length not stated 0% to 80% Stated by the maker

Long probe meters

The long probe meters are built around a 20 inch reinforced stainless steel probe. The Courdom HT-M listing says to push the probe into dense square or round hay bales to check moisture below the surface after baling, before storage, or before transport, and it lists alfalfa, forage and mixed hay as the intended use. The Fynoyf listing gives the same 20 inch probe, the same 8% to 45% moisture range and the same 32°F to 210°F temperature range, and it supports checks in several spots in the same bale. The AgraTronix HT-Pro listing also lists a 20 inch probe with a calibration clip and an illuminated LCD display, though its moisture range is 8% to 44% rather than 8% to 45%. A long probe suits a full bale, where the middle is the part you cannot see or feel.

Compact meters

The Soonkoda HM-B is the compact option in this set, with a 15.7 inch probe in the title and a probe length of 40cm with a total length of 58cm in the bullets. Its moisture range is 3% to 40%, and it runs on 4 AA batteries. The listing states a resolution of 0.1% below 20% and 1% at 20% or higher, which is the finest resolution stated anywhere in this set. The listing also describes a “CAL+/-” button that adjusts the moisture value range from -9 to 16, with temperature compensation settings that start at 0 for +10℃ to +35℃.

Meters that read temperature

Several listings read temperature alongside moisture. The Courdom and Fynoyf listings both read temperature from 32°F to 210°F on the same screen as the moisture figure. The Runant TK100H (on Amazon) listing says the screen automatically detects real-time temperature, while the kalageen TK100H (on Amazon) listing says its meter operates at temperatures ranging from -10 to 60 degrees Celsius but cannot measure temperature, so the two listings for the same model name disagree on this point. The kalageen listing also gives a half a year warranty and a measurement time of 1 second, with a moisture range of 0% to 80% and accuracy of ±0.5%.

Reading the moisture range

Moisture range is the figure that differs most between listings, so compare it before anything else. The Courdom and Fynoyf meters read from 8% to 45%, the AgraTronix HT-Pro reads from 8% to 44%, the Soonkoda HM-B reads from 3% to 40%, and the TK100H listings read from 0% to 80%. The Soonkoda listing states its resolution plainly, at 0.1% below 20% and 1% at 20% or higher, and the Runant and kalageen listings state an error range of 0.5%.

None of these listings converts a moisture figure into a storage decision, so treat the reading as a comparison tool: check the same bale in several spots, check bales from the same cutting against each other, and watch for a bale that reads far wetter than its neighbours.

Using the probe in a bale

How you push the probe in matters as much as the meter itself. The Soonkoda listing says to insert the probe vertically and quickly into the material, then press and hold the red button on the handle while the screen shows the result, and to use the same technique when checking the same material more than once. The Runant listing adds that the deeper the probe is inserted, the more accurate the value will be.

Check several spots in a large bale, since moisture is rarely even through a bale. The Courdom listing describes pushing the probe into dense square or round bales to check moisture below the surface after baling, before storage, or before transport. A backlit LCD display helps in a dark barn or at dawn, and every listing here that mentions a display describes a backlit screen. The Courdom kit also includes a carry bag, a calibration clip and a 20 inch probe, and it runs on 1x 9V battery, not included.

Temperature readings and calibration

Calibration is what keeps a meter honest over a season of use. The Courdom listing includes a calibration clip to help verify readings before checking, with a reference value of 24.7% ±1.5%, and the Fynoyf listing includes the same clip. The Soonkoda listing takes a different route, with a “CAL+/-” button that adjusts the moisture value range from -9 to 16 according to temperature compensation, set to 0 for +10℃ to +35℃ and to 1 for -5℃ to +10℃.

The Courdom listing gives a 3-minute auto-shutoff, the Fynoyf listing gives an auto power-off function, and the kalageen listing offers a choice between manual and automatic shutdown. The Courdom meter runs on 1x 9V battery, not included, while the Soonkoda meter (on Amazon) runs on 4 AA batteries.

Read the listing twice

Moisture meter listings contradict themselves often, and the numbers that conflict are usually the ones you need to plan around:

  • Courdom HT-M and HT-Pro: the two listings share identical bullets, and only the model number and colour differ, Black against Slate Black, so the listings read as near duplicates of the same meter.
  • AgraTronix HT-Pro: its moisture range is 8% to 44%, against 8% to 45% on the Courdom and Fynoyf listings, and its spec table gives dimensions of 2.0 x 30.0 x 7.0 inches with a weight of 2.0 pounds.
  • Soonkoda HM-B: the title says a 15.7 inch probe, while the bullets say the probe length is 40cm and the total length is 58cm, so the same probe is described in different units in different parts of the listing.
  • TK100H listings: the Runant listing says the screen detects real-time temperature, while the kalageen listing says the same model operates from -10 to 60 degrees Celsius but cannot measure temperature. The ZOEYEC listing for the same model gives almost no figures at all beyond a weight stated as 0.22 pounds.
  • Fynoyf: the same listing appears in Black and in BlackYellow, with identical bullets and the same 20 inch probe.

Measure the bale you need to check before ordering, and allow for the larger probe figure where listings disagree.

What this guide does not cover

This guide covers meter hardware only. It does not cover how much hay a goat needs, hay types or any health question. Ask your veterinarian or local extension office about rations and goat health.

FAQs from goat keepers

How does a moisture meter work on a hay bale?

Push the probe into the bale and the meter reads the moisture inside on its screen. The Runant listing states the working principle is conductivity, with automatic temperature compensation, and the Soonkoda listing describes pressing and holding the red button on the handle, after which the display jumps from “P1” to the measured moisture value.

What moisture range does a hay meter read?

It depends on the listing. Courdom and Fynoyf meters read from 8% to 45%, the AgraTronix HT-Pro reads from 8% to 44%, the Soonkoda HM-B reads from 3% to 40%, and the TK100H listings read from 0% to 80%.

Do hay moisture meters read temperature too?

Some do. The Courdom and Fynoyf listings read temperature from 32°F to 210°F alongside moisture, while the kalageen TK100H listing says its meter operates from -10 to 60 degrees Celsius but cannot measure temperature, so check the listing for the model you buy.

How do you calibrate a hay moisture meter?

Use the calibration clip or the calibration button the listing describes. The Courdom listing includes a calibration clip with a reference value of 24.7% ±1.5%, and the Soonkoda listing describes a “CAL+/-” button that adjusts the moisture value range from -9 to 16.

What batteries does a hay moisture meter use?

It depends on the model. The Courdom meter runs on 1x 9V battery, not included, while the Soonkoda meter runs on 4 AA batteries, and several listings add an auto power-off function to save battery life between checks.

More from the barn

See every hay feeder guide and all hay net guides.

More picks: best hay tarps, best slow feeding hay net, best hay net for square bales and best goat hay feeder for wall.