
On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
WAIWL Fence Post Repair Kit9.7/10View on Amazon - 2
VANCASTLE Fence Post Repair Kit9.7/10View on Amazon - 3
Goovilla Fence Post Repair Kit9.7/10View on Amazon
A goat with its head through the fence is the usual way a wire fence repair starts, found at the morning check when the hay is already late. Wire fence repair means finding the sag or the break, pulling the wire tight again, and joining or clipping it so the fence holds until the next round. This guide walks through each step with the tools and kits the listings state, from cable tie guns to fence wire tighteners, and points out where those listings contradict themselves.
GoatGearLab earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
Wire fence repair: the short answer
Start with a walk of the whole line before touching any tool. Mark every sag, every broken strand and every leaning post, then fix the posts first, the wire second and the mesh last, since a tight wire on a leaning post sags again by the next storm. Most repairs need only a wire tightener or a handful of clips, a splice sleeve or a few cable ties, and a post repair kit for the posts that lean.
If you would rather go straight to the tools, the fence repair kit guide lines up the kits by pieces and sizes.
Four ways to fix a fence
The listings in this guide fall into four repair types. The table shows what each one does and the figure the maker states.
| Repair | Example listing | Stated figure | What it fixes |
|---|---|---|---|
| Cable tie gun kit | DAFONSO 112-piece kit | 110 ties, 11.8 inch, 200 lb tensile | Lashing mesh and chain link |
| Wire tightener clips | Fijaru 50-pack kit | 50 clips, 1/4 in, 500 lb tension | Sagging barbed wire |
| Wire fixer | HOTYELL fence wire fixer | 6.9 lb, wires 0.9-5.0 mm | Stretching loose wire |
| Post repair kit | HuaSheWJ post kit | 33.62 inch pile, 2.3 mm steel | Leaning wood posts |
Cable tie guns and zip ties
A cable tie gun tightens and cuts stainless steel ties in one motion, which makes it the fast choice for lashing chain link and mesh back to a post or rail. The DAFONSO kit (on Amazon) lists 110 stainless steel ties at 11.8 inches with a 200 lb tensile strength, plus the gun and a release tool. The Balabulala kit lists 100 black stainless steel ties at 11.8 inches, and the Krenzia kit (on Amazon) lists 300 ties in two sizes with an organizer, gloves, scissors and a storage bag. Stainless ties resist UV and rust where plastic ties dry out and snap, according to the makers. See the best wire fence ties guide for more tie options.
Wire tighteners and clips
A wire tightener pulls a sagging strand back to tension without re-stringing the run. The Fijaru kit lists 50 galvanized steel clips at 1/4 inch with a forged steel handle, and the maker states the clips withstand 500 lb tension with a 5:1 mechanical advantage and a 5-year warranty against breakage. The clips fit 8-12 gauge wire, and the maker states a 60-second install with no tools needed. A second listing for the same kit offers 30 clips instead of 50, so check the count before ordering. See the best fence stretcher for goat fence guide for more stretchers.
Wire fixers and stretchers
A fence wire fixer is a hand tool that grips the wire, pulls it tight and latches it, which suits a single broken or slack strand in the middle of a run. The HOTYELL fixer (on Amazon) lists a 6.9 lb high-carbon steel body with a stainless steel chain and a serrated grip for plain, barbed and electric wire from 0.9 to 5.0 mm. The HONOLAYA tool (on Amazon) lists a 6.5 lb steel frame with an adjustable jaw width of 1/4 to 3/8 inch for wire from 1.5 to 5.0 mm, and a lifetime replacement promise for manufacturing defects. Both tools work on smooth, barbed and electric wire, so match the jaw and the wire size before buying.
Post repair kits
A leaning post needs a repair kit, not more wire tension. The HuaSheWJ kit (on Amazon) lists a 33.62 inch pile built from 2.3 mm thick steel, with hex screws and a two-piece splicing design that needs no excavation and no pre-drilling. The maker states it fits 4×4 and 6×6 posts and 4 ft and 6 ft columns, and it is not suitable for concrete surfaces. The kit anchors a sloping wood post back to firm support, which keeps the wire above it from sagging again. See how to fix a loose fence post and the leaning fence post repair kit guide for more post options.
Tighten sagging wire first
Walk the line and mark every sag with a bit of flagging tape or a twist of wire, so nothing gets missed. Start at the end that still runs straight and work toward the sag, threading the wire through a clip, seating the clip in the handle and turning until the strand runs straight. The Fijaru clips fit 8-12 gauge wire, and the HONOLAYA jaw adjusts from 1/4 to 3/8 inch, so check the wire size against the tool before starting. Check the tension by hand when done: a tight strand hums when plucked and does not belly between posts.
Do not over-tighten. A strand pulled drum-tight in cool weather can snap when the sun heats it, and a clip seated on rusted wire can slip. If the wire is rusted through at the sag, cut it out and splice in a fresh piece instead of pulling the old strand tighter.
Splice a broken strand
A clean break needs a splice, not a knot. Cut back to sound wire on both sides, overlap the ends and join them with a crimping sleeve, then crimp with the tool in the kit. The YingYa kit lists a crimping plier with 4 adjustable positions from 0.1 to 2.2 mm, 100 ft of 1/16 inch 304 stainless steel cable, 100 aluminum crimping sleeves and 10 wire rope thimbles. For a quick field fix, a stainless steel cable tie can lash mesh or a light strand, but it is not a substitute for a crimped splice on a tensioned strand. See the best fence wire splice kit guide and the best fence crimping tool guide for more splice options.
Reset a leaning post
A post that leans takes the wire with it, so fix the post before tensioning anything. Drive the repair pile beside the post, bolt it on with the hex screws in the kit and check the post with a level as you go. The HuaSheWJ kit needs no excavation and no pre-drilling, and its cutting-tail screws are stated to resist splitting the wood. The kit is not suitable for concrete surfaces, so a post set in concrete needs a different fix. Once the post stands straight, re-tension the wire above it.
Read the listing twice
Fence repair listings often contradict themselves, and the numbers that conflict are usually the ones you need to plan the repair:
- Krenzia: 8 and 12 inch ties in the title against 7.8 and 11.8 inch ties in the bullets.
- Balabulala: 12 inch ties in the title against 11.8 inch ties in the bullets.
- Fijaru: the same FS02 kit is listed as a 50-pack and as a 30-pack, so check the clip count before ordering.
- XUTTUM: the 200 piece count covers the ties; the gun and the shears come on top of the 200 ties.
Measure the wire size and the post size before ordering, and allow for the larger figure when two figures disagree. Some listings also promise more than the tool can do; read the stated figures and leave the rest out.
What this guide does not cover
This guide covers wire and post hardware only. It does not cover fence charger installation, energizer settings or grounding; check the charger maker manual and the best electric fence charger for goats guide for those. For animal questions, ask your veterinarian or local extension office.
FAQs from goat keepers
Can you repair a wire fence without replacing the whole run?
Yes. Tighten the sagging strands, splice the breaks and reset the leaning posts, and replace only the section that is rusted through or broken in several places.
What tool tightens sagging barbed wire?
A fence wire tightener kit with clips and a handle, such as the Fijaru kit with 50 clips at 1/4 inch and a stated 500 lb tension, or a hand wire fixer such as the HOTYELL tool for wire from 0.9 to 5.0 mm.
Can cable ties fix a chain-link fence?
Yes, for lashing mesh back to a post or rail. Stainless steel ties at 11.8 inches with a 200 lb tensile strength resist UV and rust where plastic ties dry out and snap, according to the makers.
How do you fix a leaning fence post?
Anchor it with a post repair kit. The HuaSheWJ kit lists a 33.62 inch steel pile that needs no excavation and fits 4×4 and 6×6 posts, but it is not suitable for concrete surfaces.
What gauge wire do fence tightener clips fit?
The Fijaru clips fit 8-12 gauge wire. Check the wire size against the clip size before ordering, since a clip that is too small will not seat.
More from the barn
See every goat fencing guide and all fencing and shelter guides.
More picks: wire fence ties, fence stretchers for goat fence, fence repair kits and wire fence for goats.
