Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Galvanized Stock Tank Drain Plug Size: What Fits Your Tank

Galvanized stock tank drain plug size depends on the tank: Rubbermaid tanks take a 1-1/4 or 1-1/2 inch plug, and this guide compares plug kits on threads, gaskets and fittings.

Top picks

As an Amazon Associate I earn from qualifying purchases.

How we score

Galvanized Stock Tank Drain Plug Size: What Fits Your Tank
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1htskwa 304 Stainless Plughtskwa 304 Stainless Plug9.6/10View on Amazon
  2. 2Sxmprail Plug and Faucet KitSxmprail Plug and Faucet Kit9.5/10View on Amazon
  3. 3Ana Ark Stainless Faucet KitAna Ark Stainless Faucet Kit9.5/10View on Amazon
  4. 4VYH Rubbermaid Plug KitVYH Rubbermaid Plug Kit9.4/10View on Amazon

The tank is green, the goats need fresh water and the drain plug in your hand does not fit the hole in the tank. Galvanized stock tank drain plug size comes down to the thread: most Rubbermaid tanks take a 1-1/4 or 1-1/2 inch plug, and the plug must match the hole it screws into. This guide explains how to measure the hole, read the threads and pick a plug kit that seals the first time.

GoatGearLab earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

htskwa 304 Stainless Plug

htskwa 304 Stainless Plug

htskwa9.6/10 GoatGear Score
i
The GoatGear Score runs from 0 to 10 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 304 stainless steel drain plug kit that handles draining and sealing for Rubbermaid tanks, with 1-1/4 and 1-1/2 inch threads and a rubber gasket.

Pros

  • 304 stainless steel construction meeting lead-free standards
  • 1-1/4 and 1-1/2 inch male and female threads
  • Rubber gasket and thread sealant tape included
  • Reverse-thread design for easier installation

Cons

  • No faucet or hose connector is included
  • No warranty term with a stated length is given
  • No reducer is included for a 3/4 inch hose fitting
  • Listed fit covers Rubbermaid tanks only
Sxmprail Plug and Faucet Kit

Sxmprail Plug and Faucet Kit

Sxmprail9.5/10 GoatGear Score
i
The GoatGear Score runs from 0 to 10 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A drain plug kit that handles draining, reducing and pouring, with a 1-1/4 inch plug, a 1-1/4 x 3/4 inch reducer and a 3/4 inch brass faucet.

Pros

  • Five-year free replacement is stated
  • Includes a 1-1/4 x 3/4 inch pipe reducer and a 3/4 inch brass faucet
  • Two rubber gaskets, a rubber outer ring and two pre-wrapped plumber's tapes included
  • Nut is 8 millimeters thick for a deeper thread grip

Cons

  • Plug and reducer are high-density ABS plastic, not stainless steel
  • No lead-free standard is stated
  • 7 pieces in the kit, so more parts to keep track of
  • Faucet adds another threaded joint that can leak
Ana Ark Stainless Faucet Kit

Ana Ark Stainless Faucet Kit

Ana Ark9.5/10 GoatGear Score
i
The GoatGear Score runs from 0 to 10 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A drain plug kit that handles draining through a garden hose, with a 3/4 inch NPT by 3/4 inch GHT stainless steel faucet and no reducer fittings.

Pros

  • Stainless steel faucet with a 3/4 inch NPT by 3/4 inch GHT hose connector
  • Full-bore, large-diameter valve for unobstructed water flow
  • Double-layer leak-proof seal with a silicone gasket and thread seal tape
  • Needs no reducer fittings for installation

Cons

  • No warranty term is stated
  • No lead-free standard is stated
  • Plug thread size is stated only through the 3/4 inch faucet fitting
  • Spec table gives only 1.0 inch dimensions, so plug size must be read from the title
VYH Rubbermaid Plug Kit

VYH Rubbermaid Plug Kit

VYH9.4/10 GoatGear Score
i
The GoatGear Score runs from 0 to 10 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A drain plug kit that handles draining and cleaning for Rubbermaid tanks, with 1-1/4 and 1-1/2 inch threads, a silicone gasket and thread seal tape.

Pros

  • 1-1/4 and 1-1/2 inch male and female threads
  • Double-layer leak-proof design with a silicone gasket and thread seal tape
  • Installs and removes without tools
  • Installation guide ropes and thread sealant tape included

Cons

  • No warranty term is stated
  • No faucet or hose connector is included
  • Plug is high-density plastic, not stainless steel or brass
  • Title gives a 2 inch hole size that does not match the 1-1/4 and 1-1/2 inch threads, so the fit needs checking

As an Amazon Associate I earn from qualifying purchases.


Also worth comparing

Galvanized stock tank drain plug size: the short answer

Measure the drain hole, then match the thread. The kits in this guide list 1-1/4 and 1-1/2 inch male and female threads, and they fit Rubbermaid tanks of 50, 70, 100, 150 and 300 gallons. A galvanized tank drains the same way, so match the thread in the hole, not the size of the tank. A plug with a rubber or silicone gasket and thread seal tape seals the joint, and a faucet fitting turns the drain into a hose outlet.

Measure the hole first

Measure across the drain hole with calipers or a ruler, and check whether the hole has threads or a smooth edge for a fitting to pass through. The VYH listing says its kit fits holes of 2 inches and up, while its plug threads are 1-1/4 and 1-1/2 inch, so a hole measurement and a thread measurement are two different numbers. Write the measurements down before ordering.

Threads: NPT, GHT and what fits

Threads decide the fit. NPT threads are tapered pipe threads that seal a plumbing joint, and the kits here list 1-1/4 inch NPT fittings. GHT threads are garden hose threads, and the Ana Ark kit lists a 3/4 inch NPT by 3/4 inch GHT stainless steel faucet, so one end screws into the plug and the other takes a garden hose. A reducer bridges the gap: the Sxmprail kit (on Amazon) includes a 1-1/4 by 3/4 inch pipe reducer. Match the plug thread to the tank, and the faucet thread to the hose you plan to use. The water trough sizes guide covers tank gallons and dimensions.

Materials: plastic, stainless steel and brass

Material sets how long a plug lasts in water and weather. High-density plastic, as the VYH and Sxmprail listings state, resists water and costs less than metal, but it can wear at the threads over time. Stainless steel, as the htskwa and Ana Ark listings state, resists corrosion and holds its threads, and htskwa lists 304 stainless steel meeting lead-free standards. The black vs galvanized stock tank guide compares tank materials.

Gaskets, tape and leak-proofing

A plug seals with a gasket and tape, not with force. The kits here use a rubber or silicone gasket pressed between the plug and the tank wall, and thread seal tape wrapped around the threads fills the gaps a gasket cannot reach. The VYH and Ana Ark listings call this a double-layer leak-proof design, and the Sxmprail kit adds two rubber gaskets, a rubber outer ring and two pre-wrapped tapes. Wrap the tape in the direction of the threads, tighten the nut by hand, snug it with a wrench, and check for drips after the first fill. A nut with a thicker grip, as the Sxmprail listing states with a nut 8 millimeters thick, threads on deeper and holds a tighter seal.

The drain plug kits

Each kit below handles the same job, draining and sealing the tank, with a different mix of plug, threads, gasket and faucet.

FAQs from goat keepers

What size drain plug does a Rubbermaid stock tank take?

A 1-1/4 or 1-1/2 inch plug. The kits in this guide list 1-1/4 and 1-1/2 inch male and female threads and fit Rubbermaid tanks of 50, 70, 100, 150 and 300 gallons. Measure the hole in your tank before ordering, since the thread must match.

What is the difference between NPT and GHT threads?

NPT threads are pipe threads that seal a plumbing joint, while GHT threads are garden hose threads. The Ana Ark kit lists a 3/4 inch NPT by 3/4 inch GHT faucet, so one end fits the plug and the other takes a garden hose.

Do I need a reducer for a stock tank drain plug?

Only if the faucet is smaller than the plug. The Sxmprail kit includes a 1-1/4 by 3/4 inch pipe reducer, while the Ana Ark kit needs no reducer fittings at all.

Stainless steel or plastic drain plug: which lasts longer?

Stainless steel holds its threads longer in water and weather. The htskwa kit (on Amazon) lists 304 stainless steel meeting lead-free standards, while the VYH and Sxmprail kits list high-density plastic, which can wear at the threads over time.

How do I stop a stock tank drain plug from leaking?

Use a gasket and thread seal tape, and tighten the nut well. The kits here use a rubber or silicone gasket with seal tape, and the Sxmprail kit adds two rubber gaskets, a rubber outer ring and two pre-wrapped tapes. Check for drips after the first fill and snug the nut again if the joint weeps.

htskwa 304 Stainless Plug
Still deciding? Our top pickhtskwa 304 Stainless Plug
Check price on Amazon

Behind the Farm Score

The GoatGear Score weighs performance, build, value, safety and warranty. Safety here means lead-free materials and a seal that keeps tank water in. One kit states a warranty term, the Sxmprail five-year free replacement, so warranty plays a part in its ranking and no part in the others. The How we pick page explains the weights.

More from the barn

See every water trough guide and all feeding and water guides.

More picks: stock tank vs water bucket, black vs galvanized stock tank, round stock tanks and water trough sizes.