
On this page
A goat standing on the fence at milking time is the usual sign the pen needs a rethink, and goat pen set up starts with the panels, the gate and the shade before the goats ever move in. This guide walks through the job step by step: pick a dry spot, set the panels, hang the gate, add shade and check every joint before the first goat walks through the gate. Every figure below comes from a listing for the panels and screens compared here, and the guide points out where those listings contradict themselves.
GoatGearLab earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
Goat pen set up: the short answer
Start with the spot, then the panels, then the gate and the shade. A flat, dry patch near the barn beats a low corner that holds water after rain. Panels go up in a square or a rectangle with the gate where the wheelbarrow and the feed buckets pass through, and a shade screen goes on the sunny side. Measure the spot against the panel sizes in the table below before ordering, because the listings disagree on a few figures.
Panel sizes compared
| Panel | Stated size | Height | Notes |
|---|---|---|---|
| Rite Farm 5 ft x 5 ft stall kit | 5 ft x 5 ft | 40 inches | 6 rail, welded aluminum |
| Rite Farm 5 ft x 10 ft stall kit | 5 ft x 10 ft | 40 inches | 6 rail, welded aluminum |
| Country Manufacturing side panel | 36 inches wide | 42 inches | 3/4 inch square tube, 16 gauge |
| Wesnoy shade screen | 144 x 59 inches | Not stated | HDPE mesh, grommets, 30 cm cable ties |
Starter stalls
A starter stall is the base unit everything else connects to. The Rite Farm 5 ft x 5 ft stall kit is a 6 rail panel set at 40 inches tall, listed at 60.0 x 60.0 x 40.0 inches and 34.0 pounds, made from welded aluminum in Saltillo, Texas. The 5 ft x 10 ft stall kit doubles the length at 120.0 x 120.0 x 40.0 inches and 50.0 pounds, with the same 6 rail build at 40 inches tall. Each kit is part of the maker’s aluminum series goat and sheep panel, pen and stall system, so panels from the same series connect to each other.
Add-on kits
Add-on kits extend a stall that already stands, and the Rite Farm listings are plain about the order of work: the add-on note says to buy a full starter stall first, then the add-on kit that connects to it. The 5 ft x 5 ft wall-mounted add-on kit weighs 18.0 pounds, and the 5 ft x 10 ft add-on stall kit lists 120.62 x 63.25 x 40.0 inches at 38.0 pounds with a 1 Year warranty. The 12 pack of panels takes a different route: 11 panels and 1 gate panel at 180.0 x 180.0 x 40.0 inches and 136.0 pounds, which covers a pen with a gate in the same box.
Wall-mounted stalls
A wall-mounted stall kit anchors to a barn wall instead of standing free. The Rite Farm 5 ft x 5 ft wall-mounted stall kit lists 60.0 x 60.0 x 40.0 inches at 28.0 pounds, and the 5 ft x 10 ft wall-mounted stall kit lists 120.0 x 120.0 x 40.0 inches at 48.0 pounds, each a 6 rail panel set at 40 inches tall in welded aluminum. A wall mount suits a barn with a solid wall and saves the floor space a freestanding pen would take.
Side panels and shade
Side panels close the gaps a stall kit leaves open. The Country Manufacturing side panels (on Amazon) are 42 inches tall and 36 inches wide, built from 3/4 inch square tube at 16 gauge with 5/16 round steel bars, and the listing sells them in a pack of 2. For shade, the Wesnoy screen (on Amazon) is a 144 x 59 inch sheet of HDPE mesh with reinforced webbing and rustproof grommets, fixed with cable ties about 30 cm long that come in the package. The maker describes the mesh as UV-resistant, and the screen suits round pens, chicken coops, cattle pens, horse stables and sheep pens as well as goat pens.
Pick a spot for the pen
Put the pen on high, dry ground near the barn, where the morning chores run short and the ground dries after rain. Leave room around the pen for a wheelbarrow, for hay bales and for a gate that swings wide enough to carry a feed bucket through with hands full. Keep the pen clear of low spots where water stands, and keep it close enough to the barn that winter water and hay stay a short walk away. A pen beside a fence line or a barn wall can use that wall as a side, which is where the wall-mounted stall kits fit.
Gates and getting in and out
Plan the gate before the panels go up, because a gate added last rarely lands where the chores need it. The Rite Farm 12 pack includes 1 gate panel among its 11 panels, which puts the gate in the same box as the pen. Hang the gate where the feed buckets and the wheelbarrow pass through, and check that it swings clear of the water bucket and the hay rack. A gate latch that a goat can nose open is no latch at all, so fit a latch made for goat pens and check it from the outside before the goats move in. See the gate latches for goat pens for latch styles.
Shade and windbreaks
Goats need shade in summer and a windbreak when the weather turns. The Wesnoy screen at 144 x 59 inches covers a long run of panels with one sheet, and its rustproof grommets and 30 cm cable ties fix it to the panels without extra hardware. Hang the screen on the sunny side of the pen and leave the lower edge clear of the ground so air moves under it. A screen also breaks the wind and gives the goats a private corner, which the maker lists as part of the screen’s job.
Read the listing twice
Pen and panel listings often contradict themselves, and the numbers that conflict are usually the ones needed to plan the layout:
- Wesnoy shade screen: 144 x 59 inches in the title and the bullets, against 13.78 x 11.81 x 5.12 inches in the spec table. The spec table figures describe the package, not the screen, so trust the title and the bullets for the screen size.
- Rite Farm 4 pack: 4 pack in the title, 1 item in the spec table NumberOfItems. The title and the bullets agree on 4 panels, so that is the count to trust.
- Rite Farm 12 pack: 12 pack in the title with 11 panels and 1 gate panel, against 1 item in the spec table. The title and the bullets agree on 12 panels, so that is the count to trust.
- Rite Farm 5 ft x 10 ft add-on: 120.62 x 63.25 x 40.0 inches in the spec table against 120.6 inches long by 63.3 inches wide by 40.0 inches high in the Size field. The figures agree once rounded, so either figure plans the same pen.
Measure the spot before ordering and allow for the larger figure where the listing disagrees with itself.
What this guide does not cover
This guide covers pen hardware only: panels, gates, shade and layout. It does not cover feeding, milking, shelter heating or any health question. Ask a veterinarian or the local extension office about rations and goat health.
FAQs from goat keepers
How tall should a goat pen fence be?
The listings here give 2 heights: Rite Farm panels stand 40 inches tall, and Country Manufacturing side panels stand 42 inches tall. Pick the height that matches the panels already in the pen.
How big is a 5 ft x 5 ft stall kit?
The Rite Farm 5 ft x 5 ft stall kit lists 60.0 x 60.0 x 40.0 inches at 34.0 pounds, with 6 rails in welded aluminum. The wall-mounted version lists the same size at 28.0 pounds.
Can I add panels to a stall I already own?
Yes, with an add-on kit, and the Rite Farm listings say to buy a full starter stall first, then the add-on kit that connects to it. The 5 ft x 5 ft wall-mounted add-on kit weighs 18.0 pounds, and the 5 ft x 10 ft add-on stall kit carries a 1 Year warranty.
What covers a pen for shade?
The Wesnoy screen covers 144 x 59 inches in HDPE mesh with rustproof grommets and cable ties about 30 cm long. Hang it on the sunny side of the pen.
Do the panels come with a warranty?
A 1 Year warranty is stated on the Rite Farm 4 pack of panels and on the 5 ft x 10 ft add-on stall kit. The other listings here state no warranty term.
More from the barn
See every goat fencing guide and all fencing and shelter guides.
More picks: best electric fence for goats, best fence for goats and sheep, best gate latch for goat pens and goat shelters.
