Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Install T Post Fence: Line, Posts and Wire

How to install t post fence with a driver that fits the post, from marking the line and driving the posts straight to hanging the wire and walking the line again.

Top picks

As an Amazon Associate I earn from qualifying purchases.

How we score

How to Install T Post Fence: Line, Posts and Wire
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Generic 30mm Hex T-Post DriverGeneric 30mm Hex T-Post Driver9.6/10View on Amazon
  2. 2Scryphalon 12 LB T Post DriverScryphalon 12 LB T Post Driver9.6/10View on Amazon
  3. 3MTZUL SDS Max T-Post DriverMTZUL SDS Max T-Post Driver9.6/10View on Amazon
  4. 4Swellisher 8 lb T Post DriverSwellisher 8 lb T Post Driver9.5/10View on Amazon

How to install t post fence starts with a straight line of posts and a driver that fits them. A goat leaning on the fence will find the loose post first, so the posts have to go in straight and solid before any wire goes up. The drivers below cover the job from a one-person manual driver to attachments for a rotary hammer and a jackhammer.

GoatGearLab earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

Generic 30mm Hex T-Post Driver

Generic 30mm Hex T-Post Driver

Generic9.6/10 GoatGear Score
i
The GoatGear Score runs from 0 to 10 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A jackhammer attachment that sets T-posts without lifting the machine overhead.

Pros

  • Sets T-posts without lifting the machine overhead
  • Fits 30mm hex and most modern 1-1/8 inch hex jackhammers
  • Forged, hardened and tempered steel bit and collar
  • Lifetime warranty on the bit and collar is stated

Cons

  • Jackhammer is not included
  • Will not drive posts through solid rock or concrete
  • Needs a 60-Joule jackhammer
  • Will not fit a shank smaller than 29.6mm across flats
Scryphalon 12 LB T Post Driver

Scryphalon 12 LB T Post Driver

Scryphalon9.6/10 GoatGear Score
i
The GoatGear Score runs from 0 to 10 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

A 12-pound manual driver with angled handles for one-person driving.

Pros

  • 12-pound steel body with a 2.7-inch inner diameter
  • 160-degree angled dual handles for lift and drop control
  • Black powder-coated finish resists rust
  • One-person job with no partner needed

Cons

  • No warranty term is stated
  • Manual lift and drop only, so long runs take more work
  • Odd post sizes need measuring first
MTZUL SDS Max T-Post Driver

MTZUL SDS Max T-Post Driver

MTZUL9.6/10 GoatGear Score
i
The GoatGear Score runs from 0 to 10 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An SDS-Max rotary hammer attachment for driving T-posts and ground rods.

Pros

  • 2-inch socket takes T-posts up to 2 inches, or 51mm
  • 0.3-inch metal wall for impact resistance
  • Forged steel with full quenching heat treatment
  • Fits SDS-Max rotary hammers and demolition hammers

Cons

  • Cannot fit SDS-Plus hammers, jack hammers or spline hammers
  • Care for two years is mentioned without a warranty term
  • Needs an SDS-Max rotary hammer, which is not included
Swellisher 8 lb T Post Driver

Swellisher 8 lb T Post Driver

Swellisher9.5/10 GoatGear Score
i
The GoatGear Score runs from 0 to 10 and weighs performance (35%), build (25%), value (25%), safety (10%, where it applies) and warranty (5%), using only what the manufacturer and the listing publish. How we pick ›

An 8-pound manual driver with two handles for lift-and-drop driving.

Pros

  • 8-pound body is heavy enough to drive posts by dropping
  • Tubular design with a closed-end cap spreads impact across the post top
  • Two welded handles for lift and drop control
  • Coated to resist rust and corrosion

Cons

  • No inner diameter is stated
  • No warranty term is stated
  • No socket or post-size range is stated

As an Amazon Associate I earn from qualifying purchases.


Also worth comparing

How to install t post fence: the short answer

Mark a straight line, set the corner and end posts first, drive the line posts with a driver that fits the post, then hang the wire and walk the line again. A manual driver suits a short run, while a rotary hammer or jackhammer attachment suits a long run or hard-packed ground. Measure the post before buying the driver, since the socket has to fit the post: the manual drivers here take a 2.7-inch opening and a standard T-post, the SDS-Max bit takes posts up to 2 inches, or 51mm, and the jackhammer bit takes a 30mm hex shank. Our best T-post drivers for goat pens roundup scores more drivers on these points.

Driver styles compared

Driver Style Weight Socket or fit Power needed Amazon
Scryphalon 12 LB T Post Driver Manual, two handles 12 LB 2.7-inch inner diameter None, manual View on Amazon
Swellisher 8 lb T Post Driver Manual, two handles 8 lb Not stated None, manual View on Amazon
MTZUL SDS Max T-Post Driver Rotary hammer attachment Not stated 2-inch inside diameter SDS-Max rotary hammer View on Amazon
Generic 30mm Hex T-Post Driver Jackhammer attachment Not stated 30mm hex shank 60-Joule jackhammer View on Amazon

The two manual drivers need no power at all: the Scryphalon driver (on Amazon) is a 12-pound steel body with a 2.7-inch inner diameter, while the Swellisher driver (on Amazon) is an 8-pound steel body with no inner diameter stated. The powered attachments trade weight for machine power: the MTZUL bit fits an SDS-Max rotary hammer, and the jackhammer bit fits a 30mm hex shank and calls for a 60-Joule jackhammer.

Step 1: Mark the line and set the corners

Walk the fence line first and clear brush and loose rock from the path. Mark the corner and end posts, set those first and brace them, then mark the line posts between them so the run stays straight. A post that starts crooked stays crooked once the wire pulls on it, and corner and end posts carry the pull of the wire from the whole run, so check them twice before moving on to the line posts.

Step 2: Drive the line posts

Slide the driver over the top of the post, grip both handles and lift and drop with a smooth, controlled motion, letting gravity do the work. The Scryphalon handles angle inward at 160 degrees so the elbows stay close to the body, and the Swellisher handles are welded on for lifting and dropping with control. Keep the driver straight on the post, and stop to check that the post is still plumb before driving it further. A manual driver drives T-posts, U-channel posts, round metal posts and wooden stakes, and the closed-end cap on the Swellisher driver spreads the impact across the post top so wooden posts split less. For hard-packed ground, the powered attachments take over: the MTZUL bit runs on an SDS-Max rotary hammer, and the jackhammer bit runs on a 60-Joule jackhammer without lifting the machine over the head.

Step 3: Hang the wire and walk the line

Once the posts stand straight, hang the wire from the first post to the last, keeping it at the same height along the run. Walk the line again and look down it from each end, since a post that leans shows up clearly against the wire. A post that moved during driving gets pulled and reset before the wire goes tight, not after. The fence is done when every post stands straight and the corners hold firm.

The drivers for this job

The drivers below cover the driving step in different ways: the manual drivers run on lift and drop, and the attachments run on machines the reader may already own.

How to choose a t post driver

Manual or powered

A manual driver is the simplest choice for a short run: the Scryphalon driver is a 12-pound steel body and the Swellisher driver is an 8-pound steel body. A powered attachment suits a long run or hard-packed ground, but it needs the machine to go with it: the MTZUL bit needs an SDS-Max rotary hammer, and the jackhammer bit needs a 60-Joule jackhammer that is not included.

Check the fit first

The socket has to fit the post, and the listings state the fit plainly. The Scryphalon driver has a 2.7-inch inner diameter for most standard T-posts, U-channel posts, round metal posts and wooden stakes. The MTZUL bit has a 2-inch inside diameter, a 2-1/2-inch outside diameter and a 1-9/16-inch socket depth for posts up to 2 inches, or 51mm. The jackhammer bit fits 30mm hex shanks, PH65 or J65-type, and most modern 1-1/8 inch hex jackhammers with a round top, and will not fit a shank smaller than 29.6mm across flats. The Swellisher listing states no inner diameter, so its fit has to be checked another way. See T-post driver vs sledgehammer for the comparison on the same job.

Weight and handles

Weight is what drives the post on a manual driver. The Scryphalon driver is 12 pounds with dual handles angled inward at 160 degrees, and the Swellisher driver is 8 pounds with two welded handles. The 17-inch Scryphalon body keeps the tool compact between job sites, and the listing states that the top cap is fully reinforced and welded to the body.

FAQs from goat keepers

Can one person drive T-posts alone?

Yes. The Scryphalon listing describes its driver as a one-person job with no partner needed, and the Swellisher listing describes two handles for lift and drop control.

What size driver fits a standard T-post?

The Scryphalon driver has a 2.7-inch inner diameter for most standard T-posts. The MTZUL bit has a 2-inch inside diameter and takes posts up to 2 inches, or 51mm.

Can a rotary hammer drive T-posts?

Yes, with the right attachment. The MTZUL bit fits SDS-Max rotary hammers and demolition hammers, but cannot fit SDS-Plus hammers, jack hammers or spline hammers.

Will a jackhammer attachment drive posts through rock?

No. The jackhammer attachment listing states that it will not drive posts through solid rock or concrete, and that a 60-Joule jackhammer is recommended.

How heavy is a manual T-post driver?

The Scryphalon driver is 12 pounds and the Swellisher driver is 8 pounds. The powered attachments list no weight.

Generic 30mm Hex T-Post Driver
Still deciding? Our top pickGeneric 30mm Hex T-Post Driver
Check price on Amazon

More from the barn

See every fence post driver guide and all fencing and shelter guides.

More picks: best T-post drivers for goat pens, manual T-post drivers, T-post driver vs sledgehammer and how to put in a fence post.