Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

Easy Install Fence Posts: Gas and Hand Drivers Compared

Easy install fence posts with gas drivers and hand drivers, compared on stated power, weight, sleeves, and fit for T-posts and wooden posts.

Easy Install Fence Posts: Gas and Hand Drivers Compared
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Zareba 4-Foot Step-in Electric Fence PostsZareba 4-Foot Step-in Electric Fence PostsView on Amazon
  2. 241" Systems Pig Tail Step-in Electric Fence Post for Livestock41" Systems Pig Tail Step-in Electric Fence Post for LivestockView on Amazon
  3. 3VEVOR 3 ft Fence PostVEVOR 3 ft Fence PostView on Amazon
  4. 4VEVOR 6 ft Fence PostVEVOR 6 ft Fence PostView on Amazon
  5. 5VEVOR 5 ft Fence PostVEVOR 5 ft Fence PostView on Amazon
  6. 672CC Gas Powered Post Hole Digger with 3 Auger72CC Gas Powered Post Hole Digger with 3 AugerView on Amazon

A fence post that leans after a storm leaves the whole line sagging, and the goats find the weak spot before the weekend is out, which is why easy install fence posts matter more than the fence wire itself. Easy install fence posts are the drivers and the steps that set a post straight and firm with less digging, less lifting, and less guesswork. A gas driver hammers the post down while you hold it steady, and a hand driver does the same work with a lift and a drop. This guide compares the drivers the listings describe, the sleeves that fit the posts, and the steps that set a post straight.

Also worth comparing

GoatGearLab earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

Easy install fence posts: the short answer

Start with the driver, then check the sleeve, then set the post. A gas driver suits a long fence line, where the engine does the hammering, and a hand driver suits a short run of posts, where a lift and a drop is enough. The sleeve must fit the post: the listings here state sleeves from 49mm to 100mm on the gas drivers, and a 2.7 inch interior diameter on a hand driver. Set the post straight, drive it to depth, and check it again before moving to the next post.

For the full post-setting routine, see the how to use post driver guide, which walks through the steps on fence posts.

Drivers compared

Driver Type Stated power Weight Sleeves
JKCHEN PRO Gas, 52cc 1900W, 6500 RPM, 55J 42.0 pounds 3 sleeves, 49mm, 69mm, 100mm
HIGOSPRO Gas, 37.7cc 1200W, 8500 RPM, 35J 15.4 lbs 2 sleeves, 55mm, 70mm
YOHSUGO Hand Not stated 12 lb Not stated
yarlung Hand Not stated 17 lbs Interior 2.7 inch diameter, 11 inch deep
iHYTOON Hand Not stated Not stated Not stated

Gas drivers

Gas drivers hammer the post for you. The JKCHEN PRO driver (on Amazon) lists a 52cc 2-stroke engine at 1900W and 6500 RPM, with 55J of impact energy, a 1.3L fuel tank, and 3 sleeves at 49mm, 69mm, and 100mm. The HIGOSPRO driver (on Amazon) lists a 37.7cc 4-stroke engine at 1200W and 8500 RPM, with 35J of impact energy, a 0.65L fuel tank, and 2 sleeves at 55mm and 70mm. Both listings include a tool bag with wrenches and a priming funnel, and both state a 1 Year warranty. The JKCHEN PRO driver weighs 42.0 pounds, while the HIGOSPRO weighs 15.4 lbs, so the HIGOSPRO is the lighter gas driver to carry along the fence line.

Hand drivers

Hand drivers need no fuel and no engine. The YOHSUGO driver (on Amazon) weighs 12 lb and measures 17 inches, with 160°-angled handles and a black powder coating, and the listing recommends wearing gloves during use. The yarlung driver (on Amazon) weighs 17 lbs, measures 9 inches wide by 17 inches high, and has an interior 2.7 inch diameter that runs 11 inches deep. The iHYTOON driver (on Amazon) is a steel hand pounder with an open-head design that drops straight over standard steel T-posts, and its listing states no weight or size. Each hand driver uses the same motion: place the driver over the post, lift, and drop.

Sleeves and fit

The sleeve is the socket that grips the post, and it must match the post size. The JKCHEN PRO driver includes 3 sleeves at 49mm, 69mm, and 100mm, and the HIGOSPRO driver includes 2 sleeves at 55mm and 70mm. The yarlung hand driver has no sleeves; its interior measures 2.7 inches across and 11 inches deep, and the post must fit inside that opening. Check the sleeve or the interior against the post before buying, and check the post type too: the listings cover T-posts, U-posts, and wooden posts.

Setting a post step by step

Mark the line, set the post in place, and drive it straight. Place the driver over the top of the post, lift, and drop with controlled force, and check the post for plumb as it goes down. The YOHSUGO listing describes the same motion as lift, raise, and drop, and the yarlung listing says to lift and hammer until the post is buried to the depth you want. Wear gloves during use, as the YOHSUGO listing recommends, and keep hands clear of the post top while the driver falls.

For a long run of posts, a gas driver saves the lifting: the engine hammers while you guide the driver. For a short run, a hand driver is enough, and it needs no fuel, no mix, and no warm-up. Either way, drive the post to depth before moving on, and tamp the soil around the base so the post stands firm.

Choosing between gas and hand drivers

Choose by the length of the fence line and the ground under it. Gas drivers suit hard-packed soil and long runs: the JKCHEN PRO driver lists 55J of impact energy and the HIGOSPRO lists 35J, and both run on gas with tanks of 1.3L and 0.65L. Hand drivers suit short runs: the YOHSUGO driver at 12 lb and the yarlung driver at 17 lbs lift easily, and neither needs fuel. The iHYTOON listing states no weight, so compare it by its steel build and open-head design rather than by a figure.

What this guide does not cover

This guide covers post drivers and the steps that set a post only. It does not cover fence wire, post spacing, or any health question. Ask your local extension office about fence layout and goat fencing.

FAQs from goat keepers

What is the easiest way to install a fence post?

Use a driver that matches the job. A gas driver hammers the post down while you guide it, and a hand driver works with a lift and a drop. The JKCHEN PRO gas driver lists 1900W and 55J, while the YOHSUGO hand driver weighs 12 lb and measures 17 inches.

Do gas post drivers need mixed fuel?

It depends on the engine. The JKCHEN PRO listing states a 25:1 gas/oil mix and a 1.3L fuel tank. The HIGOSPRO listing says to add fuel and start working, with no assembly required.

What size sleeve fits a T-post?

Check the sleeve sizes the listing states. The JKCHEN PRO driver includes sleeves at 49mm, 69mm, and 100mm, and the HIGOSPRO driver includes sleeves at 55mm and 70mm. The yarlung hand driver has an interior 2.7 inches across and 11 inches deep instead of sleeves.

How heavy is a hand post driver?

The listings state 12 lb for the YOHSUGO driver and 17 lbs for the yarlung driver. The iHYTOON listing states no weight, so compare it by its steel build and open-head design.

Do hand post drivers work on wooden posts?

Yes, per the listings. The YOHSUGO driver is listed for wooden posts and U-channels, and the yarlung driver is listed for metal U-posts, T-posts, and garden wooden fence posts.

More from the barn

See every post driver guide and all fencing and shelter guides.

More picks: how to use a post driver, how to install a T-post fence and manual T-post drivers.