
On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
FOREHOGAR Fence Post Driver with Handle 12LB9.7/10View on Amazon - 2
Insaga Enhance Fence Post Driver with Anti-Slip Handles9.7/10View on Amazon - 3
Toriexon 4FT Fence Posts9.7/10View on Amazon
A leaning post in the goat pen is a chore waiting to happen, which makes fence post best practices worth getting right before the fence does the deciding. Set each post for the load it carries, walk the line for trouble, and pull failed posts with a puller matched to the post instead of your back. Every number below comes from an Amazon listing for a fence post puller we compared in our roundup, and we point out where those listings contradict themselves.
GoatGearLab earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
Fence post best practices: the short answer
Start with the right setting method: drive line posts into firm ground and set gate, corner and end posts in concrete, since a post that starts loose only gets worse. Walk the fence line for lean, rot and wobble, and replace failed posts promptly instead of shoring them up. For removal, match the puller to the post: a lever puller for T-posts, a cable and chain kit for broken or concrete-set wood posts, and a farm jack when the post refuses to move.
If you would rather go straight to the tools, our best T-post puller for chain roundup lines up pullers by type and stated specs.
Puller types side by side
| Type | Example listing | How it pulls | Stated size or rating |
|---|---|---|---|
| Lever plate puller | TNCZHYLX 36 inch puller | Plate and chain grip the T-post; lever action lifts it | 36 inches; 14.12 pounds |
| Lever puller with chain | Zwinz 36 inch puller | 52 inch lifting chain; lever principle | 36 inches high; 23 pounds |
| Lever puller, wide base | VEVOR 32 inch puller | 43 inch lifting chain; widened base resists tipping | Supports up to 661 lbs; 18.52 pounds |
| Adjustable lever puller | Dolibest puller | Telescoping handle; 5MM thickened base | Handle 36 to 49 inches; 14.52 pounds; chain not included |
| Jack attachment | Hi-Lift PP-300 Post Popper | Attaches directly to T-posts; lifts straight out | 1-1/2 inch square steel tubing; 20 pounds; 30 day warranty |
| Cable and chain kit | Feroca post remover | Galvanized cable loops the post; chain connects to a jack or lever | 5,000+ lbs pull force; 1.68 pounds |
| Farm jack | VEVOR 48 inch farm jack | 7,000 lbs capacity; doubles as a puller with a chain | Lifting range 4.13 to 40.74 inches; 27.1 pounds |
How a post puller works
Lever pullers turn a long handle and a pivoting base into lifting force. The Zwinz listing describes the motion: stand the tool upright with the handle near waist height, fit the lock around the stud, push the handle down to pull the post upward, then raise the handle back up and fit it around a lower stud and repeat. The widened base on models like the VEVOR 32 inch and the Dolibest keeps the tool from sinking or tipping while you work.
Cable and chain kits take a different route: they convert a jack or lever you already own into a puller. The Feroca kit loops a galvanized cable around the post and threads a 1/4 inch chain through the jack, and the F and P kit loops its 7/32 inch cable low around the post and hooks its 1/4 inch chain to a jack or 4×4 lever. Tighten, lift, and the snare-style grip tightens on its own as the post rises.
Match the puller to the post
T-posts are the easy case: the Hi-Lift PP-300 (on Amazon) attaches directly to them, and plate pullers like the TNCZHYLX are shaped for T-posts and chain gauges. Wood posts need a grip that will not slip on round or square stock: the Feroca kit loops its cable around 4×4 posts, and the SUOWEEI kit is listed for 4×4, round wood and residential picket posts.
Broken, rotted or concrete-set posts are where cable kits earn their keep. The Feroca listing says its kit handles broken and rotted 4×4 posts and is suitable for concrete-set posts, with no digging or hammering required. The F and P listing makes the same claim for leaning, stuck, rotted or buried posts. For a post that still will not move, the VEVOR 48 inch farm jack brings 7,000 lbs of lifting capacity to the job.
Pull, do not fight
A post that leans, wobbles at the base or shows rot is telling you it is done, and pulling it beats fighting it. Clear the area, pick the puller that fits the post, and lift straight so the hole stays clean for the replacement. The Feroca maker claims a broken post can come out in 15 minutes with the cable kit, which is a maker claim, not a promise.
After the pull, set the replacement for the load it will carry. A line post can go back in driven, while a gate or corner post deserves concrete. Keeping a puller on hand means a failed post is an afternoon job, not a fence emergency.
Read the listing twice
Puller listings are mostly consistent, but the dimensions deserve a closer look:
- TNCZHYLX: 36 inches in the title against 33.86 inches in the spec table dimensions.
- Hi-Lift PP-300: 41 inches item length against 40.5 inches in the spec table dimensions.
- VEVOR farm jack: 48 inches in the title against 48.2 inches in the spec table.
The differences are small, but the spec table is the number to plan around. Also note what is not in the box: the Dolibest and TUGNOSTI listings state the lifting chain is not included.
What this guide does not cover
This guide covers post setting, inspection and pulling tools only. It does not cover fence layout, wire choice or goat health. Check local rules for fencing near roads and property lines, and ask your veterinarian about anything health related.
FAQs from goat keepers
How do I use a fence post puller?
Stand the tool upright with the handle near waist height, fit the lock around the post or stud, and push the handle down to lift. Raise the handle back up, fit it around a lower point, and repeat until the post comes free.
How does a fence post puller work?
Lever pullers multiply your force through a long handle pivoting on a wide base. Cable kits loop a steel cable around the post and lift it with a jack or lever, and the grip tightens on its own as the post rises.
How do I pull out a fence post set in concrete?
Use a cable and chain kit listed for concrete-set posts. Loop the cable low around the post, hook the chain to a jack or lever, and lift straight; the Feroca and F and P listings both describe this method with no digging required.
How does a T-post puller work?
The Hi-Lift PP-300 attaches directly to T-posts and applies lifting force straight up the post. Plate-style pullers like the TNCZHYLX grip the T-post with a plate and chain and lift with lever action.
How much is a fence post puller?
Prices move with the seller and the season, so we do not publish them here. Our best T-post puller for farm jack roundup links each listing, where the current price shows.
More from the barn
See every post driver and puller guide and all fencing and shelter guides.
More picks: driver vs auger, fence post drivers for wood posts, T-post drivers for clay soil and T-post pullers for chain.
