Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Support a Fence Post: Bracing Options

How to support a fence post with a cable brace kit, a repair stake or diagonal bracing, using the sizes, gauge and fit the listings state.

How to Support a Fence Post: Bracing Options
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1Gtongoko 12LB T Post Driver with HandlesGtongoko 12LB T Post Driver with HandlesView on Amazon
  2. 2Gtongoko 8LB T Post Driver with HandlesGtongoko 8LB T Post Driver with HandlesView on Amazon
  3. 3Gtongoko 18LB T Post Driver with HandlesGtongoko 18LB T Post Driver with HandlesView on Amazon
  4. 4Metal Fence Posts Heavy Duty U-Post Stakes for Wire FencingMetal Fence Posts Heavy Duty U-Post Stakes for Wire FencingView on Amazon

A goat leans on the same fence post every morning on the way to the hay, and after a season of that attention the post leans with it. This guide covers how to support a fence post with a cable brace kit, a repair stake or diagonal bracing, using the figures the listings state. Every number below comes from a listing for a fence post brace or repair kit, and the guide points out where those listings contradict themselves.

Also worth comparing

GoatGearLab earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

How to support a fence post: the short answer

Start by checking how far the post leans and whether it still stands firm at the base. A post that leans but holds firm can be pulled back with a cable brace kit or held with a repair stake. A post that wobbles at the base needs a repair stake with diagonal rods, and a post that has rotted at the ground line needs replacing rather than bracing. Once the post is steady, check the fence line again after the next rain, since wet soil lets a leaning post move further.

For the hardware itself, the leaning fence post repair kit guide compares the options, and the how to fix a loose fence post guide covers resetting a post that has come loose.

Brace kits, repair stakes and diagonal bracing

Method Example listing Stated figures Fits
Cable brace kit Gripple GPAK4 16.5 ft cable, GP Large Joiner Wooden or metal posts
Repair stake KPJCI repair kit 11-gauge steel, 7.87 x 2.2 x 31.5 in 4 x 4 and 6 x 6 posts, 2.5 ft to 8 ft heights
Diagonal rods KPJCI repair kit Two diagonal support rods Leaning wood posts

Cable brace kits

A cable brace kit pulls a leaning post back toward straight and holds it there with a tensioned cable. The Gripple GPAK4 kit lists a 16.5 ft cable and a GP Large Joiner, and the maker says it suits wooden and metal post bracing and installs in less than one minute. The cable is high grade zinc aluminum with a galvanized coating, which the maker lists for corrosion resistance. The same kit is listed as a 5-pack and as a 1-pack, so check the pack count on the listing before ordering. A cable kit suits a post that still stands firm at the base and only needs pulling back into line.

Repair stakes

A repair stake drives into the soil beside a leaning wood post and bolts to it, so the post borrows the stake’s footing. The KPJCI kit (on Amazon) lists 11-gauge steel, a size of 7.87 x 2.2 x 31.5 inches, and a fit for 4 x 4 and 6 x 6 wooden posts with post heights from 2.5 ft to 8 ft. The kit ships as 2 pieces with V-shaped tips and buffer blocks, and the maker says to drive the pile into the soil with a hammer and tighten the screws. The finish is a durable anti-rust powder coat. A stake suits a post that leans at the base or has lost its footing, and the maker lists it for garden posts, farm fencing, mailbox posts and boundary fences.

Diagonal bracing

Diagonal bracing adds a rod from the post down to a point on the ground or to the next post, so the post cannot lean further. The KPJCI kit builds this in: two integrated diagonal support rods on the upper section form a triangular bracing system, and the lower section forms a T-shaped geometry once assembled. A diagonal brace suits a long fence run where the end or corner post takes the pull of the wire, and it also steadies a gate post that carries a gate. Check that the brace lands on firm ground and that the fixings hold before the goats lean on the fence again.

Check the post before bracing it

Bracing a post that has rotted through at the ground line wastes the brace, so check the base first. Push the post and watch where it moves: movement at the ground line points to rot or a failed footing, while movement along the whole post points to a lean the brace can correct. Look for soft wood, cracks and soil that has pulled away from the post. If the post moves freely at the base or the wood crumbles, replace the post and fit a brace from the start.

Read the listing twice

Fence post listings contradict themselves, and the numbers that conflict are usually the ones needed to plan the job:

  • KPJCI: 5.4 lbs in the bullets against 13.45 pounds in the spec table, so the weight of one stake is unclear.
  • Gripple GPAK4: the same kit is listed as a 5-pack and as a 1-pack, with the same 16.5 ft cable in both listings.

Measure the post and check the pack count before ordering, and allow for the larger figure where the listing gives two.

What this guide does not cover

This guide covers post support hardware only. It does not cover fence layout, wire tension, gate hanging or setting a new post in concrete. For those jobs, see the how to set fence post in concrete guide and the fencing and shelter guides.

FAQs from goat keepers

How do I support a leaning fence post?

Pull it back with a cable brace kit such as the Gripple GPAK4, or hold it with a repair stake such as the KPJCI kit. Check the base first: a post that has rotted at the ground line needs replacing rather than bracing.

What size post does the KPJCI repair kit fit?

The KPJCI kit lists a fit for 4 x 4 and 6 x 6 wooden fence posts, with post heights from 2.5 ft to 8 ft. The kit is 11-gauge steel and measures 7.87 x 2.2 x 31.5 inches.

How long is the cable in the Gripple brace kit?

The Gripple GPAK4 listing states a 16.5 ft cable with a GP Large Joiner. The kit suits wooden and metal posts, and the maker says it installs in less than one minute.

Can a brace kit be used on metal posts?

Yes, for the Gripple kit: the listing states it is suitable for wooden and metal post bracing. The KPJCI kit is listed for wooden posts only.

How heavy is the KPJCI repair stake?

The listing gives 2 figures: 5.4 lbs in the bullets and 13.45 pounds in the spec table. Confirm the weight on the listing before ordering, since the 2 figures cannot both describe the same piece.

More from the barn

See every goat fencing guide and all fencing and shelter guides.

More picks: how to brace a fence post, wooden fence post repair kit, how to level fence post and how to use post driver.