
On this page
Top picks at a glance
As an Amazon Associate I earn from qualifying purchases.
- 1
WORKIT 72CC Post Hole Digger9.7/10View on Amazon - 2
PRIJESSE 72cc Post Hole Digger9.6/10View on Amazon - 3
PROYAMA 54cc Post Hole Digger9.5/10View on Amazon - 4
VASGOR 3-Piece Auger Bit Set9.4/10View on Amazon
A goat leaning hard on a fence post can turn a straight fence line into a leaning one, and a leaning post usually starts with a hole that was never dug right. How to use a post hole auger comes down to marking the line, matching the bit to the post, starting the engine, letting the auger cut, and lifting it clear to drop the soil beside the hole. This guide walks through those steps with the diggers listed below, from gas-powered units with several bit sizes to a drill-powered bit set for planting holes.
GoatGearLab earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.
| # | Product | GoatGear Score | Buy |
|---|---|---|---|
| 1 | WORKIT 72CC Post Hole Digger | 9.7/10 | Buy on Amazon |
| 2 | PRIJESSE 72cc Post Hole Digger | 9.6/10 | Buy on Amazon |
| 3 | PROYAMA 54cc Post Hole Digger | 9.5/10 | Buy on Amazon |
| 4 | VASGOR 3-Piece Auger Bit Set | 9.4/10 | Buy on Amazon |

WORKIT 72CC Post Hole Digger
A 72cc gas-powered digger with 4, 6 and 12 inch bits, 20 and 30 inch extension rods, and an emergency stop switch on the handle.
Pros
- 72cc engine with 4, 6 and 12 inch bits for a range of hole sizes
- 20 and 30 inch extension rods for deeper digging
- Emergency stop switch on the handle for quick shutdown
- EPA Certification stated in the listing
Cons
- No warranty term is stated
- Needs a 50:1 gasoline-to-oil mix, so fuel must be mixed before use
- 32.28 x 23.62 x 18.9 inch size needs a fair amount of storage room
- Only 3 bit sizes, with no 8 inch bit in the set

PRIJESSE 72cc Post Hole Digger
A 72cc gas-powered digger with 4, 8 and 12 inch bits and 2 extension rods of 24 inches each, built for one or two people.
Pros
- 72cc engine with 4, 8 and 12 inch bits
- 2 extension rods of 24 inches each for deeper holes
- Anti-skid, vibration-proof grips on the handles
- Finger throttle and switch control on the handlebar
Cons
- No warranty term is stated
- No 6 inch bit in the set
- Screws must be tightened after delivery and before use
- No fuel tank capacity or mix ratio is stated

PROYAMA 54cc Post Hole Digger
A 54cc gas-powered digger with 4, 6, 8 and 12 inch bits and 12 and 20 inch extension rods, rated at 2.4HP and 1300W.
Pros
- 4 bit sizes: 4, 6, 8 and 12 inch, the widest range here
- 54cc engine rated at 2.4HP and 1300W
- Alloy steel bits with a powder-coated finish
- Heavy-duty gearbox with ball-bearing shafts and alloy gears
Cons
- No warranty term is stated
- No safety feature such as a stop switch is stated
- Smallest engine here at 54cc
- Extension rods top out at 20 inches, shorter than the 30 inch rods on the WORKIT

VASGOR 3-Piece Auger Bit Set
A set of 3 drill-powered auger bits in 1.6, 2.6 and 3.5 inch widths by 16 inches, for a 3/8 inch hex drive drill.
Pros
- 3 bit widths in one set: 1.6, 2.6 and 3.5 inch
- Digs holes up to 16 inches deep and 3.5 inches wide
- Fits any 3/8 inch or larger chucked drill, 18V or greater
- Solid shaft design for bulbs, bedding plants and seedlings
Cons
- No warranty term is stated
- Needs a drill with a 3/8 inch chuck, sold separately
- Narrowest holes here, at most 3.5 inches wide
As an Amazon Associate I earn from qualifying purchases.
Also worth comparing
Baotree 72cc Gas Powered Post Hole Digger Earth AugerCheck price on Amazon
62CC Gas Powered Post Hole DiggerCheck price on Amazon
Electric Post Hole DiggerCheck price on Amazon
Jecoupoon 8 Inch Hydraulic Auger Compatible with 1-1.5 TonCheck price on Amazon
52cc Gas Post Hole Digger 1800W with 3 Bits & 3 ExtensionsCheck price on Amazon
Auger Point to Fit 9" and 12" Post Hole Diggers 1-1/4" ThreadCheck price on Amazon
How to use a post hole auger: the short answer
Start by marking the fence line and the spot for each post, then pick a bit that fits the post: the listings here state bits from 4 inches to 12 inches wide. Fit the bit, add an extension rod when a deeper hole is needed, and start the engine or drill. Hold the handles with both hands, let the auger cut, and lift it out of the hole often to drop the soil beside the hole. When the hole is deep enough, set the post, check it stands straight, and backfill around it.
The gear for the job
The digging step needs the auger itself, so the 4 listings below are ranked by GoatGear Score, from a 72cc gas digger with 3 bits to a drill-powered bit set for planting holes.
Pick the bit size first
Bit width decides the hole width, so match it to the post and the job. Gas diggers in this guide state bits of 4, 6, 8 and 12 inches across the listings, while the drill-powered set tops out at 3.5 inches wide, which suits bulbs and bedding plants rather than posts. A wider bit leaves room to set and straighten the post, while a narrow bit suits planting holes where the post never goes in.
| Digger | Bit sizes stated | Extension rods stated | Engine or drive | Amazon |
|---|---|---|---|---|
| WORKIT 72CC Post Hole Digger | 4, 6 and 12 inch | 20 and 30 inch | 72cc gas, 2-cycle | View on Amazon |
| PRIJESSE 72cc Post Hole Digger | 4, 8 and 12 inch | 24 and 24 inch | 72cc gas, 2-stroke | View on Amazon |
| PROYAMA 54cc Post Hole Digger | 4, 6, 8 and 12 inch | 12 and 20 inch | 54cc gas, 2-cycle, 2.4HP, 1300W | View on Amazon |
| VASGOR 3-Piece Auger Bit Set | 1.6, 2.6 and 3.5 inch by 16 inch | Not stated | 3/8 inch hex drive drill, 18V or greater | View on Amazon |
Set up the digger
Before digging, fit the bit and any extension rod, and read the listing notes. The WORKIT digger (on Amazon) lists a 50:1 gasoline-to-oil mix and a 1.4L fuel tank, so its fuel is mixed before use. The PRIJESSE listing asks the buyer to tighten the screws after receiving the goods and before use, to avoid loose screws from long-term transportation. The VASGOR set needs a drill with a 3/8 inch chuck or larger, and the listing recommends a drill of 18V or greater. Keep the auger clean from soil and debris when not in use.
Dig, lift and clear
With the engine running, hold the handles, let the auger cut through soil and clay, and lift it out often to clear the soil. The PROYAMA listing states an easy-start system and an ergonomic handle design for control and less fatigue during extended digging jobs. The WORKIT digger lists an emergency stop switch on the handle for quick shutdown, and its grip has an anti-vibration design, while the PRIJESSE listing states anti-skid, vibration-proof grips and a finger throttle on the handlebar. The PRIJESSE listing also states the auger can be handled by one or two people, which helps when a hole needs another person at the handles.
Read the listing twice
Listings for augers can disagree with themselves, and the VASGOR set is the example here. Its title lists bits of 1.6 by 16, 2.6 by 16 and 3.5 by 16 inches, and its bullets state holes up to 16 inches deep and 3.5 inches wide, yet its spec table lists the size as 12 inch by 3.2 inch. Trust the title and bullets over the spec table. The gas diggers agree with themselves on bits and rods, but they leave gaps: the PROYAMA listing states no fuel tank capacity, and the PRIJESSE listing states no mix ratio, so those figures are simply not stated.
FAQs from goat keepers
What size auger bit does a fence post need?
Match the bit to the post, with room to set and straighten it. The gas diggers here state bits of 4, 6, 8 and 12 inches, so a post hole can be cut wider than the post itself. The VASGOR set tops out at 3.5 inches wide, which suits planting holes rather than fence posts.
Can a drill-powered auger bit dig a fence post hole?
It can dig a narrow hole, but not a post hole. The VASGOR set fits a 3/8 inch hex drive drill of 18V or greater and digs holes up to 16 inches deep and 3.5 inches wide, which suits bulbs, bedding plants and seedlings. For fence posts, use a gas digger with a 4, 6, 8 or 12 inch bit.
How do extension rods change the digging depth?
Extension rods add reach between the engine and the bit, so the hole can go deeper without changing the digger. The PROYAMA set includes 12 and 20 inch rods, the WORKIT set includes 20 and 30 inch rods, and the PRIJESSE set includes 2 rods of 24 inches each.
What fuel mix does a gas post hole digger use?
The WORKIT listing states a 50:1 gasoline-to-oil mix and a 1.4L fuel tank. The PROYAMA and PRIJESSE listings state no mix ratio and no fuel tank capacity, so those figures are not stated for those diggers.
Do any of these post hole diggers state a warranty?
No. None of the 4 listings states a warranty term, so each product card notes that no warranty term is stated. The WORKIT listing does state EPA Certification, and the PRIJESSE listing states anti-skid, vibration-proof grips.
More from the barn
See every goat fencing guide and all fencing and shelter guides.
More picks: post hole digger tips, how to dig a fence post hole, wood fence post sizes and post hole auger tips.
