Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How Deep Should a Fence Post Be?

How deep a fence post should be depends on post height, soil and load, with corner and gate posts set deeper than line posts, and drivers sized by stated weight and sleeves.

How Deep Should a Fence Post Be?
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1ARKSOLDIER 33.62 in Fence Post Repair KitARKSOLDIER 33.62 in Fence Post Repair Kit9.7/10View on Amazon
  2. 2Grazeline Fence Post Repair Kit 2-PackGrazeline Fence Post Repair Kit 2-Pack9.7/10View on Amazon
  3. 3Postsaver Pro-Set Fast Fixing Foam for Fence and Deck PostsPostsaver Pro-Set Fast Fixing Foam for Fence and Deck Posts9.7/10View on Amazon

How deep should a fence post be? It depends on how tall the post stands above ground, what the soil is like, and how much push the fence will take from goats leaning on it. This guide walks through the factors that set the depth, then the driving and setting steps, using figures from post driver listings where a number is stated.

GoatGearLab earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

How deep should a fence post be: the short answer

Set the post deep enough that it stands plumb and firm when goats lean on it and the wind pushes the fence. The deeper the post sits, the more soil holds it, and the firmer the set. Corner posts, gate posts and end posts carry more load than line posts, so they need a deeper set than a post in the middle of a straight run. In soft or wet soil, go deeper than in hard, packed soil; in rocky soil, depth is limited by what the driver can reach and what the ground allows.

What decides the depth

Post height above ground sets the lever. A tall post gives the wind and the goats more to push against, so it needs more post in the ground to hold it. A short post in a low fence needs less.

Soil sets the grip. Hard, packed soil holds a post firm at a shallower set, while soft, wet or loose soil lets a post shift, so the post needs to sit deeper to find a firm hold. Rocky soil can stop a driver short, and in that case the depth is whatever the ground allows, with the post set as deep as the driver can take it.

Load sets the rest. Corner posts take the pull of fence lines from two directions, gate posts carry the weight of the gate and the swing, and end posts take the pull of the whole run. Line posts in a straight run carry the least, so they can sit shallower than the posts that anchor the fence.

Frost also matters where winters freeze the ground: soil that freezes can lift a shallow post.

Post drivers in the reference listings

The listings below are the reference drivers for this guide. They show the weight and power a driver brings to the job, and the sleeve sizes that fit over a post.

Driver Drive Weight Impact Sleeves
JKCHEN PRO 52cc gas Gas, 1900W 42.0 pounds 55J 49, 69 and 100 mm
HIGOSPRO 37.7cc gas Gas, 1200W 15.4 pounds 35J 55 and 70 mm
YOHSUGO hand driver Hand, 17 inches 12 lb Not stated Not stated
yarlung hand driver Hand, 17 inches 17 lb Not stated Not stated
iHYTOON hand pounder Hand Not stated Not stated Not stated

Gas drivers

Gas drivers bring an engine to the job. The JKCHEN PRO driver (on Amazon) is a 52cc 2-stroke gas driver at 1900W and 6500 RPM with a 55J impact, a 1.3L fuel tank and a 0.6L/h consumption rate on a 25:1 gas/oil mix, and it weighs 42.0 pounds. The HIGOSPRO driver (on Amazon) is a 37.7cc 4-stroke gas driver at 1200W and 8500 RPM with a 35J impact, a 0.65L fuel capacity and a weight of 15.4 pounds. Both include sleeves: the JKCHEN driver includes 49 mm, 69 mm and 100 mm sleeves, and the HIGOSPRO driver includes 55 mm and 70 mm sleeves.

Hand pounders

Hand pounders are a steel tube with handles that drops over the post. The YOHSUGO driver (on Amazon) weighs 12 lb at 17 inches, with 160°-angled handles and a black powder coating that resists corrosion. The yarlung driver (on Amazon) weighs 17 lb, measures 9 inches wide by 17 inches high, with an interior 2.7 inches in diameter and 11 inches deep. The iHYTOON hand pounder (on Amazon) is a thick-walled steel tube with an open-head design that drops over standard steel T-posts, and its listing states no dimensions or weight.

Driving a post step by step

Mark the line first, then set each post where it belongs: corners and ends first, then the line posts between them. Stand the post in the hole or on the mark, and check it stands plumb before driving.

Drop the driver over the top of the post. The YOHSUGO listing describes the motion as lift, raise and drop, and the yarlung listing describes lifting and hammering many times until the post is buried to the depth you want. Keep the driver straight over the post so the force goes down the post, not sideways.

Drive in short runs and check the post often. Sight along the fence line and check the post stands plumb from each side before it goes too deep to adjust. If the post leans, pull it back and reset it rather than forcing it deeper at an angle.

Stop when the post sits at the depth you want and stands firm. A post that wobbles by hand needs more depth or a firmer set; a post that stands firm under a push is set. For the driving step itself, see our how to use a post driver guide.

Hand pounder or gas driver

A hand pounder suits a short run of posts and a keeper who wants no fuel, no engine and no extra weight to carry. The YOHSUGO driver at 12 lb and the yarlung driver at 17 lb are carried by hand, and the iHYTOON pounder needs no fuel at all. The work is the lifting: the driver goes up and comes down on the post, many times per post, so a long fence line means a long day of lifting.

A gas driver suits a long run, hard ground or a keeper with many posts to set. The JKCHEN driver at 1900W and 55J and the HIGOSPRO driver at 1200W and 35J bring engine power to the driving, with sleeves that fit over the post. The trade is weight and fuel: the JKCHEN driver weighs 42.0 pounds and runs on a 25:1 gas/oil mix, and the HIGOSPRO driver weighs 15.4 pounds with a 0.65L fuel capacity.

Setting the post firm

Backfill around the post as you drive, and tamp the fill firm so the post has soil tight against it on each side. Loose fill lets the post shift the first time a goat leans on it. Check the post stands plumb again after backfilling, since tamping can push it off line.

For a gate post, hang the gate only after the set is firm, so the gate does not pull a fresh post out of plumb. For a corner post, brace it against the pull of the fence lines before the wire goes on.

Read the listing twice

Post driver listings often leave gaps, and the numbers that matter are usually the ones you need to plan the job:

  • JKCHEN PRO: the title states 6500 RPM, 55J impact and 3 sleeves, and the spec table agrees on 42.0 pounds and a 1 year warranty; the listing gives no depth guidance for the posts it drives.
  • HIGOSPRO: the listing claims 40% less vibration than standard models, with no baseline stated for the comparison, and a 0.47L/kW·h efficiency figure that needs the maker’s own definition to use.
  • YOHSUGO: the title states 12 LB and 17 inches, and the spec table agrees, but no sleeve sizes are stated.
  • yarlung: the bullets state an interior 2.7 inches in diameter and 11 inches deep, while the spec table gives 17.0 by 9.0 by 3.0 inches; read the interior figure for fit and the outer figure for carrying size.
  • iHYTOON: the listing states no dimensions, no weight, no impact figure and no sleeve sizes at all.

Measure your posts before ordering a driver, and match the sleeve to the post.

What this guide does not cover

This guide covers post depth and driving only. It does not cover fence layout, wire choice or gate hanging, and it does not cover how deep footings must go for a barn or a shed. Ask your local extension office about frost depth and soil conditions in your area.

FAQs from goat keepers

How deep should a fence post be for goats?

There is no one figure in the listings: set corner and gate posts deeper than line posts, go deeper in soft or wet soil, and drive until the post stands firm and plumb. Ask your local extension office about frost depth in your area.

Should gate posts go deeper than line posts?

Yes. Gate posts carry the weight of the gate and the swing, so they need a deeper and firmer set than a line post in a straight run.

Can I drive a post with a hand pounder?

Yes. The iHYTOON hand pounder drops over standard steel T-posts, and the YOHSUGO driver weighs 12 lb at 17 inches with 160°-angled handles. Lift, raise and drop the driver until the post sits at the depth you want.

What size sleeve fits a T-post?

The JKCHEN driver includes 49 mm, 69 mm and 100 mm sleeves, and the HIGOSPRO driver includes 55 mm and 70 mm sleeves. Match the sleeve to the post before driving.

Do gas post drivers need fuel?

The JKCHEN driver runs on a 25:1 gas/oil mix with a 1.3L fuel tank, and the HIGOSPRO driver is a 4-stroke with a 0.65L fuel capacity. Check the mix and the tank before starting work.

More from the barn

See every fencing and shelter guide and all fence post drivers guides.

More picks: how to drive a fence post into the ground, how to dig a fence post, how to set a fence post in concrete and manual fence post driver.