Skip to content
We independently pick everything we recommend. We earn a commission when you buy through our links, at no extra cost to you. Learn more ›
Amazon Black Friday Week deals

How to Replace Fence Post Step by Step

How to replace fence post: free the old post, check the hole, set the new post and drive it home, with gas and hand driver figures from the listings.

How to Replace Fence Post Step by Step
On this page

Top picks at a glance

As an Amazon Associate I earn from qualifying purchases.

  1. 1MIWEVRO Metal Garden Fence PostsMIWEVRO Metal Garden Fence Posts9.7/10View on Amazon
  2. 2CLEASO Metal Fence PostsCLEASO Metal Fence Posts9.7/10View on Amazon
  3. 3VEVOR 6 ft U-Channel Metal Fence PostVEVOR 6 ft U-Channel Metal Fence Post9.7/10View on Amazon

A goat leans on the same fence post every morning, and the post has started to lean with it. This guide covers how to replace fence post step by step, and the method depends on the post: a wood post is set in a dug hole, while a steel T-post is pulled and a new one is driven into firm ground. Every number below comes from a listing for a post driver we compared.

GoatGearLab earns a commission when you buy through links on this page, at no extra cost to you. As an Amazon Associate I earn from qualifying purchases. Affiliate disclosure.

How to replace fence post: the short answer

Unhook the wire and clips, then pull the old post. For a wood post, clear the hole, stand the new post in it, hold it plumb, backfill and tamp the soil, or set it in concrete. For a steel T-post, do not drop it into a loose hole: stand the new post in firm, undisturbed ground along the line and drive it down with a hand driver or a gas driver. Rehang the wire and check the line, because a post that stands straight keeps the wire tight and the goats in the pen.

If you would rather start with the tools, our easy install fence posts guide compares gas and hand drivers.

Free the old post

Start with the wire. Unhook the wire and clips from the old post and set them aside, then look at how the post sits. A post that leans or wobbles by hand is ready to come out. Our how to remove a fence post guide covers the pull in detail.

Work the post loose before you pull. Rock it back and forth to break the grip of the soil, and clear loose dirt from around the base as it moves. A manual puller gives you leverage on a stubborn steel post; our manual T post puller guide covers the types. Lift the post straight out once it moves freely.

Wood post: set it in the dug hole

A wood post goes into an open hole, not under a driver. Look into the hole once the old post is out. Clear fallen dirt and roots, and check that the sides still hold their shape. A hole that has caved in needs clearing, or the post will sit crooked from the start. Our how deep should a fence post be guide covers depth.

  1. Stand the new post in the hole and hold it plumb.
  2. Check it from the side and from along the fence line, because a post that looks straight from the front can still lean along the wire.
  3. Backfill in layers and tamp the soil down as you fill so the post has no room to shift, or set the post in concrete instead.
  4. Brace the post while the fill settles if the line pulls hard on it.

Our how to brace a fence post guide covers bracing, and our how to set fence post in concrete guide covers a concrete set. A post set in concrete needs time to harden before the wire goes back on.

If the old post sat in concrete

A concrete collar has to come out before a new wood post can go in, or the new post has nowhere to sit.

  1. Unhook the wire, then dig the soil away from the sides of the concrete so the whole collar is exposed.
  2. Rock the post and collar back and forth to break the grip of the surrounding soil.
  3. Lift the post and collar out together. If the collar is too heavy to lift, break it into pieces and lift the pieces out.
  4. Clear every chunk, loose dirt and root from the hole, and check that the sides still hold their shape.
  5. Stand the new post in the cleared hole, plumb it, and backfill and tamp or pour concrete.

Our how to fix fence post in concrete guide covers concrete work in more detail.

T-post: pull it and drive the new one

A steel T-post is not set into a dug hole. Pull the old post, then stand the new post upright in firm, undisturbed ground on the fence line, with the flat side facing the wire line. Fit the driver over the top and drive the post down to its final depth, checking from the side and along the line as it goes. Ground loosened by the old post will not hold the new one well, so move the new post along the line rather than dropping it into the old hole.

A post driver does the heavy work. Hand drivers lift and drop by hand, while gas drivers use an engine to drive the post down. The listings we compared cover the range:

Driver Type Stated power or weight Sleeves or fit
JKCHEN PRO 52cc gas driver Gas, 2-stroke 1900W, 6500RPM, 55J 49mm, 69mm, 100mm sleeves
HIGOSPRO 37.7cc gas driver Gas, 4-stroke 1200W, 8500RPM, 35J 55mm, 70mm sleeves
YOHSUGO hand driver Hand 12 lb 17 inch
yarlung hand driver Hand 17 lb 9 inch by 17 inch, 2.7 inch interior
iHYTOON hand pounder Hand Not stated Open head for standard steel T-posts

Hand drivers

Hand drivers suit a short run of posts. The YOHSUGO driver (on Amazon) lists 12 lb and 17 inch, with 160°-angled handles and a black powder coating, and the listing recommends wearing gloves during use. The yarlung driver (on Amazon) lists 17 lb, 9 inch by 17 inch, and an interior 2.7 inch diameter that is 11 inch deep. The iHYTOON pounder (on Amazon) lists thick-walled, high-strength steel and an open-head design that drops over standard steel T-posts, and it states no weight at all.

Gas drivers

Gas drivers suit a long run of posts or hard ground. The JKCHEN PRO driver (on Amazon) lists a 52cc 2-stroke engine, 1900W, 6500RPM and 55J of impact, with a 1.3L fuel tank, 0.6L/h consumption and a 25:1 gas and oil mix. It lists 42.0 lb and 11.0 inches by 12.5 inches by 31.4 inches, and a 1 Year warranty. The HIGOSPRO driver (on Amazon) lists a 37.7cc 4-stroke engine, 1200W, 8500RPM and 35J of impact, with a 0.65L fuel capacity and a 15.4 lb frame. It lists 12.0 inches by 12.0 inches by 25.5 inches and a 1-year warranty, and the maker claims 40% less vibration than standard models.

Match the driver to the post

Check the sleeve or interior size against your post before you buy. The JKCHEN PRO driver ships 49mm, 69mm and 100mm sleeves, the HIGOSPRO driver ships 55mm and 70mm sleeves, and the yarlung driver lists a 2.7 inch interior diameter. The iHYTOON pounder lists an open head for standard steel T-posts. Measure your post and pick a driver whose sleeve or head fits it.

Our how to use post driver guide covers the driving motion, and our how to drive a fence post into the ground guide covers the full job.

Rehang the wire and check the line

Hook the wire back onto the new post with the same clips you saved, and work along the line to the next post. Set the wire at the height it sat before, and check that it runs straight between posts. Clip the wire on with T-post clips; our T post clips how to install guide covers the clip types.

Cap the top of a T-post once the wire is on. A safety cap covers the sharp top and marks the line; our T post safety caps guide covers the options. Walk the line after the job and look for a post that still leans or a wire that sags, and fix a loose post before it pulls the line down. Our how to fix a loose fence post guide covers the fix.

What this guide does not cover

This guide covers replacing a fence post only. It does not cover fence layout, wire choice or how much wire a run needs. Our how to lay out fence posts guide covers layout, and our manual T post driver guide covers driver choice in detail. Ask your local extension office about fence rules for your area.

FAQs from goat keepers

How do I get the old fence post out?

Unhook the wire and clips, rock the post loose and pull it straight out. A manual puller gives you leverage on a stubborn steel post; our how to remove a fence post guide covers the pull.

Do I need a gas post driver to replace a fence post?

Only for steel posts. A wood post is set in a dug hole and needs no driver. For a T-post, a hand driver suits a short run: the YOHSUGO driver lists 12 lb and the yarlung driver lists 17 lb. A gas driver suits a long run or hard ground: the JKCHEN PRO driver lists 1900W and 55J, and the HIGOSPRO driver lists 1200W and 35J.

What size driver fits a T-post?

Check the sleeve or interior size against your post. The JKCHEN PRO driver ships 49mm, 69mm and 100mm sleeves, the HIGOSPRO driver ships 55mm and 70mm sleeves, and the yarlung driver lists a 2.7 inch interior diameter. The iHYTOON pounder lists an open-head design for standard steel T-posts.

Can I reuse the same hole for the new post?

For a wood post, yes, if the hole still holds its shape and the new post stands plumb in it. Clear fallen dirt, backfill and tamp as you fill, or set it in concrete. For a T-post, drive the new post into firm ground along the line instead of dropping it into the old hole.

More from the barn

See every post driver guide and all fencing and shelter guides.

More picks: how to drive a fence post into the ground, how to use post driver, manual T post driver and how to fix a loose fence post.